Saudequip

LEGAL NOTICE & CREDITS © 2025 Saudequip

Saudequip

HOME BRANDS & PRODUCTS CAT PRODUCT LINE POWER SYSTEMS OIL AND GAS WELL SERVICE ENGINES C18 ACERT™ DRY MANIFOLD ENGINE

C18 ACERT™ DRY MANIFOLD ENGINE

Back to the list

Cat C18 ACERT engines are the ideal solution for your demanding operations in the oilfield. Decades of field operation and intense research and development allow Cat C18 ACERT engines to deliver excellent performance with low operating costs and emissions.Equipment powered by C18 ACERT engines include, pump skids, nitrogen units, acidizing units, cementing units, blenders, and hydraulic power units. Cat engines are backed by the worldwide network of Cat dealers ready to support your operation with technical support, service, parts, and warranty.C18 ACERT engines, with ratings: 429-522 bkW (575-700 bhp) @ 1800-2100 rpm, meet China Stage II, U.S. EPA Tier 3 equivalent, EU Stage IIIA equivalent emission standards. Ratings: 570-597 bkW (765-800 bhp) @ 1800-2100 rpm meet U.S. EPA Tier 2 equivalent emission standards. Ratings below 560 bkW (751 bhp) are available using U.S. EPA and EU Flexibility, and for other global regulated and non-regulated areas. Ratings above 560 bkW (751 bhp are available using U.S. EPA Flexibility and for other global regulated and non-regulated areas.

SPECIFICATIONS

Minimum Rating429.0 bkW

Maximum Rating596.0 bkW

Governor and ProtectionADEM A3

general specifications

Minimum Rating429.0 bkW

Maximum Rating596.0 bkW

Governor and ProtectionADEM A3

AspirationTurbocharged-Aftercooled

Displacement18.0 L

Flywheel and Flywheel HousingSAE No. 0 or SAE No. 1

Flywheel Teeth136 (SAE No. 0), 113 (SAE No. 1)

Rotation (from flywheel end)Counterclockwise

Stroke183.0 mm

Bore145.0 mm

emissions

EmissionsEPA and CARB Non-Road Mobile Tier 3, EU Stage IIIA

dimensions

Length1389.0 mm

Width919.0 mm

Height1227.0 mm

Weight1273.0 kg

capacity for liquids

Cooling System50.0 L

C18 ACERT™ (Dry Manifold) STANDARD EQUIPMENT

  • air inlet system
    Single turbocharger, mid-mounted, inlet 152.4 mm (6 in), hoseconnection
    Dual turbocharger, front and rear inlet 127.0 mm (5 in.), hoseconnection
  • control system
    Electronic governing, PTO speed control
    Programmable ratings
    Cold mode start strategy
    Automatic altitude compensation
    Power compensation for fuel temperature
    Programmable low and high idle and TEL
    Electronic diagnostics and fault logging
    Engine monitoring and protection system (speed, temperature,pressure)
    J1939 Broadcast (diagnostic, engine status, and control)
  • cooling system
    Thermostats and housing — outlet vertical
    Jacket water pump — gear-driven, centrifuga
    RH front water pump inlet
    All plugs/fittings are STOR for lines gp water
  • exhaust system
    Exhaust manifold — dry
    Single turbo — front-facing turbo exhaust, full marmonconnection, maximum load 10 kg for direct connection to turbo
    Dual turbo — exhaust elbow, dry 203 mm (8 in)
  • flywheels and flywheel housings
    See Mandatory Options
  • fuel system
    Electronic unit injector
    Fuel filter, secondary, mid-mount (LH 2 micron high performance)
    Fuel transfer pump, LH front
    Fuel priming pump, LH mid-mount
    Fuel sample valve, mounted on fuel filter base.
  • lube system
    Crankcase breather — rear valve cover
    Oil cooler — RH (dual)
    Oil filter — RH, LH
    Oil pan — front sump
    Oil dipstick — LH front
    Oil pump
  • mounting system
    Front support (shipping only)
  • power takeoffs
    Crankshaft pulley, 203.2 mm (8 in), 3 grooves 292.1 mm(11.5 in) 1 groove, all 15.9 mm (.63 in) width
    Hydraulic pump drive, SAE A, 11-tooth
  • general
    Vibration damper
    Paint — Cat yellow
    Lifting eyes
    Automatic variable timing, electronic
    Electronic installation kit 70-pin connector (connectors, pins,sockets)
  • mandatory options
    Throttle position sensor
    Single turbo only — exhaust system (front or rear)
    Flywheel housing or rear PTO
    Primary filter/water separator

C18 ACERT™ (Dry Manifold) OPTIONS

    • air compressor
      Air compressor governor
      Expansion chambers
    • air inlet system
      Air cleaners
      Air lines
    • charging system
      Charging alternators
      Alternator mountings
      Alternator wiring
      Circuit breakers and mountings
      Alternator belt guard
    • cooling system
      Radiator
      Fan drive with radiator packages
      Fan height instructions
      Vee belts
      Aftercooler lines with Caterpillar installed radiator
      Single turbo configuration rear-facing exhaust
      Single turbo configuration rear-facing exhaust
      Aftercoooler lines
      Suction fan adapters
      Blower fan adapter
      Blower fan
      Suction fan
      Fan belt
      Coolant level sensor
      Dry charge coolant conditioners
    • exhaust system
      Turbo exhaust connection
      Flexible fittings
      Elbows, flange, clamp, pipes
      Exhaust adapters
      Manifold
      Mufflers
    • fuel systems
      Flexible fuel lines
      Fuel filter location
      Fuel cooler
      Water separator
    • instrumentation
      Gauges and instrument panels
    • lube system
      Oil pans
      Drain and cover
      Oil level gauge
      Remote oil filters
      Oil filters
      Lubricating oils
    • mounting system
      Structural steel base
      Front and rear engine support
    • power takeoffs
      Rear enclosed clutches
      Hydraulic pump drives
      Hydraulics gear pumps
      Clutch supports
      Crankshaft pulleys
    • protection system
      Air shutoff
    • starting system
      Air starting motors
      Air pressure regulator
      Air silencer
      Start switch
      Electric starting motors — 12V, 24V
      Battery sets – 24V
      Battery cable and rack
      Starting aids
    • transmission arrangement
      Transmission water lines
Back

MOTEUR