M 32 E MARINE GENERATOR SET
The M 32 E is designed for the offshore market focused on generator set application. The 720/750 rpm concept will reduce generator costs. Charge air cooler housing and charge air cooler allow easier disassembly and cleaning. The new design still supports operation at any ambient condition without load reduction. We offer a generator set application for customers operating the engines mainly below 47 %.
SPECIFICATIONS
Minimum Rating3165 kWe (3960 kVA)
Maximum Rating5747 kWe (5940 kVA)
Emissions/Fuel StrategyIMO II
generator set specifications
Minimum Rating3165 kWe (3960 kVA)
Maximum Rating5747 kWe (5940 kVA)
generator set configurations
Emissions/Fuel StrategyIMO II
engine specifications
Bore320 mm
Stroke460 mm
Configuration6,8,9 Cylinder
Swept Volume37 L
generator set dimensions
Weight73.0 - 98.0 t (160937 - 216053 lbs)
Length9566 - 11156 mm (376.6 - 439.2 in)
Width2600 mm (102.4 in)
Height4565 - 4770 mm (179.7 - 187.8 in)
M 32 E STANDARD EQUIPMENT
- air inlet system
Air intake silencer / filter - control system
Load sharing unit (for multiple engine plant only)
Modular Alarm Control and Protection System (MACS)
Speed governor - cooling system
Electric cooling water preheater
HT cooling water pump (engine driven)
HT cooling water pump (engine driven) - exhaust system
Exhaust gas expansion joint
Exhaust gas insulated manifolds
Turbocharger at counter-flywheel end - fuel system
Fuel circulating pump (attached / for MDO/MGO only)
Fuel indicator filter
Fuel pressure valve (fitted / for MDO/MGO only) - instrumentation
Control push buttons and lamps
Local control panel
Pressure and temperature indicator - lube system
Engine with dry sump
Lube oil cooler (separate)
Lube oil pump (engine driven)
Lube oil self-cleaning filter
Oil sump in base frame
Pre-lubricating oil pump (electric driven / fitted on base frame)
Pressure regulating valve - mounting system
Flexible pipe connections
High flexible coupling
Resilient mounting on base frame - starting system
Electrical barring device
Starting air valve - general
Engine, flexible coupling and generator mounted on a common base frame
Flywheel cover
Lifting device (rental)
Torsional Vibration Calculation (TVC)
M 32 E OPTIONS
- air inlet system
Air inlet shut-off valve
Air intake transition piece
Expansion joint
Silencer / filter - control system
Air injection control (for better load acceptance)
Electronic speed governor
Remote indicators (start air pressure, engine speed, etc.)
Starter for electric driven pumps
24 DC UPS - cooling system
CW piping for generator cooling on base frame
CW piping for lubricating oil cooler on base frame
FW/SW plate cooler
HT cooling water pump (electric driven)
LT cooling water pump (electric driven)
Sea water cooling pump (electric driven)
Temperature control valve - exhaust system
Silencer (with or without spark arrester) - fuel system
Fuel oil cooler
HFO final preheater
HFO pressure regulating valve
HFO self-cleaning automatic filter
HFO supply and booster pumps (electrical driven)
HFO treatment and supply modules
HFO viscosity control device
Mixing tank - lube system
Lube oil centrifuge
Lube oil cooler fitted on base frame
Lube oil pump (electrical driven)
Lube oil treatment and combined modules
Temperature control valve - mounting system
Double resilient mounting (engine and base frame)
Engine resiliently mounted on base frame, base frame rigidly mounted - starting system
Starting air compressor
Starting air receiver - general
Engine PTO coupling
Generator customer supply
Part load optimization kit for constant speed engine (SFOC improvement, smoke reduction)
Part load optimization kit for variable speed engine (massive SFOC improvement,…)
PTO shaft on counter-flywheel side